|
2024-04-26 |
Other |
hose in pastry dish room still leaking been leaking |
Its leaking where the copper part is shoved into the hose, it has not stopped. We havent done anything to it, and i see there is no work order, so wanted to write another one. thank you! |
|
|
replaced nozzle and added gasket for hose connection |
|
2024-04-26 |
Other |
cut lock off of cleaners locker that says "Cody" on it. no rush |
|
|
|
complete |
|
2024-04-26 |
|
|
Drain condensation from air compressor tanks of both stationary air compressors |
|
|
drained |
|
2024-04-26 |
Other |
sink by CMS drain |
CMA sink drain handle is loose and won't stay open. It is currently taped with masking tape. Thanks! |
|
|
unscrewed and screwed back in. issue resolved |
|
2024-04-25 |
Other |
washing machine down |
Hi, I think Seth already told you but i wanted to put in a work order to make sure it gets on the list of items to do. thank you |
|
|
repaired |
|
2024-04-25 |
Other |
cord to a defender scale |
|
|
|
glued back together |
|
2024-04-24 |
|
|
Large wooden table in the red packaging room is wonky. Table leg currently balanced with a scrap of cardboard |
|
|
rebalanced |
|
2024-04-24 |
|
|
Wheel popped off 140qt mixing bowl base. Barely screws back in |
|
|
replaced with new wheel |
|
2024-04-22 |
Walk-In |
|
Vacuum Water from under compressors to prevent water leaking into delivery room. |
|
|
complete |
|
2024-04-22 |
HVAC |
|
Check filters and replace when necessary. Check P traps for condensation and drain as necessary. Check condensor coils. WEEKLY DURING SPRING SUMMER, MONTHLY AFTER FIRST FREEZE |
|
|
replaced all roof filters |
|
2024-04-22 |
|
|
Our lovely new 80qt paddle is a bit sharp on the edges. Can it please be dulled to avoid someone cutting their hand open? Thanks! |
|
|
used flapper wheel to take off eges |
|
2024-04-21 |
Other |
cookie machine |
A piece to the cookie machine has a broken wire. I am not sure what the part is called, but it has a wire that I believe cuts the cookie? It is a thin wire that has snapped and needs to be repaired. Thanks! |
|
|
replaced wire |
|
2024-04-19 |
Plumbing |
|
Our sink has not been getting hot, lukewarm at best the last day or 2. |
|
|
to unclog the water mixer: screw all way in and all way out multiple times to free up debris. then remove aerator and run water to clear out debris. |
|
2024-04-18 |
|
|
Can we get our backup rugelach marker etched to say "rug"? |
|
|
etched backup rugelach marker to say "RUG" |
|
2024-04-16 |
Other |
Please replace baseboard on wall where the sheeter clothes hang in bread |
very worn out etc. thanks |
|
|
Complete |
|
2024-04-15 |
Walk-In |
|
Vacuum Water from under compressors to prevent water leaking into delivery room. |
|
|
complete |
|
2024-04-15 |
HVAC |
|
Turn off make up air on pastry hvac to counter act humidity |
|
|
n/a |
|
2024-04-12 |
Oven |
|
On 12 door Oven; Blow out burners, clean |
|
|
complete |
|
2024-04-12 |
|
|
De-grease, and re-grease bowl lifter lift pole and chain. |
|
|
greased |
|
2024-04-12 |
Other |
|
Is it possible to place a hanger for a clipboard on our cabinet for our pre-op checklist? |
|
|
complete |
|
2024-04-11 |
Other |
Metal racks holding the square pans all 3 of them need rewelding in bread by the rack ovens |
few poles are off, some are loose. need to be fixed. |
|
|
rewelded |
|
2024-04-11 |
Other |
tiles by bread RO and also complete baseboard down the wall there |
in that inside little area. Baseboard needs replacing and needs be added in other spot. and also tile up against the rack oven needing replacing. |
|
|
moved with other tile orders |
|
2024-04-09 |
Other |
Floor scrubber batteries |
Check battery cell levels and flush out cleaner dilution valve |
|
|
complete |
|
2024-04-08 |
Walk-In |
|
Vacuum Water from under compressors to prevent water leaking into delivery room. |
|
|
complete |
|
2024-04-06 |
Other |
bread rack holding ingredients in scaling bread area next to black metal rack |
I red tagged it. Please cut the top poles some to fit in the LVO. thank you |
|
|
cut tops and ran through lvo |
|
2024-04-06 |
Other |
both scaling tables leg is off and looks like they going to fall down with the wieght on them |
I red tagged it. Please cut the top poles some to fit in the LVO. thank you |
|
|
needs new table |
|
2024-04-06 |
Other |
long wire ingredient rack in scaling all 4 wheels are messed up, 2 red tags on it |
I red tagged it. Please cut the top poles some to fit in the LVO. thank you |
|
|
complete |
|
2024-04-06 |
Other |
Wheels |
Grey tub caddy only has 1/4 wheels attached :( |
|
|
complete |
|
2024-04-05 |
Other |
proofer was flooded inside |
leaking somewhere perhaps? |
|
|
could not detect a leak |
|
2024-04-05 |
Other |
wheel came off wheel frame for pastry mixing bowl |
its red tagged, and the wheel is on pastry manager desk |
|
|
ordered new |
|
2024-04-04 |
Other |
bagel hose connector is leaking where it connects to the pipe. |
|
|
|
tightened |
|
2024-04-04 |
Other |
|
we have a speedrack in the cake room with a red tag, the wheels are not doing so hot and it feels unsafe for large amounts of weight. |
|
|
complete |
|
2024-04-03 |
Other |
bucket area hose attachment was off on the ground |
|
|
|
repaired |
|
2024-04-03 |
Other |
our hose is leaking good where it is connected to the end peice of it |
not where it connects to the area on the wall to hook it up it is where the hose itself meets the end. sent a picture pointing to it. if this can be fixed would be great. or else we will need a new hose |
|
|
repaired |
|
2024-04-03 |
Other |
check back drain hole of LVO area in the pit area |
The water in there in the drain itself is only about 3 inches down below the top of the grate on top. Perhaps this needs to be snaked out? Or something like that, please check thank you |
|
|
okay |
|
2024-04-02 |
Other |
Floor machine will not auto move itself |
will send email |
|
|
repaired |
|
2024-04-02 |
Other |
sink by CMS drain |
The replacement drain is loose and keeps falling, not letting the sink drain efficiently. Can we please have it tightened? |
|
|
complete |
|
2024-04-01 |
Walk-In |
|
Vacuum Water from under compressors to prevent water leaking into delivery room. |
|
|
complete |
|
2024-04-01 |
HVAC |
|
Turn off make up air on pastry hvac to counter act humidity |
|
|
complete |
|
2024-04-01 |
Plumbing |
|
Using Gas Sniffer check all gas operated for leaks or potential |
|
|
complete no issues |
|
2024-04-01 |
|
|
Need a new receiving sign put up outside of the warehouse. |
|
|
complete |
|
2024-03-31 |
Other |
Three compartment sink |
The three compartment sink in the dish room has a broken / cracked edge by the sprayer, on the table part next to the wash sink, to the left. Water leaks out of this crack. |
|
|
repaired with marine weld |
|
2024-03-27 |
Other |
re paint towel cabinet/ rusting |
Towel cabinet is rusting and has flaking and missing paint, bottom is the worst. Could you repaint and add a kick plate on bottom of doors? |
|
|
Alex will be ordering a new cabinet and replace |
|
2024-03-27 |
Other |
very squeeky double wide baking rack |
Please lube wheels on double wide. SO squeaky! Trevor red tagged. |
|
|
complete |
|
2024-03-26 |
Other |
sheet tray |
A sheet tray has a spot that is sharp. Can it be filed down? We left it by the maintenance door with a red tag indicating the spot. |
|
|
repaired |
|
2024-03-26 |
Other |
replace wheel on cart by the 9 door deck oven window |
work order was closed, there is a red tag on the wheel from last time, the cart by the 9 door deck oven, please move the cart and you will see the red tag on the wheel . thank you, |
|
|
complete |
|
2024-03-26 |
|
|
Drain condensation from air compressor tanks of both stationary air compressors |
|
|
complete |
|
2024-03-26 |
Other |
Speed Rack |
Tagged rack is missing a bolt that secures one of its wheels and supporting beams. It is the column with the tag. |
|
|
repaired |
|
2024-03-25 |
Walk-In |
|
Vacuum Water from under compressors to prevent water leaking into delivery room. |
|
|
vaccumed water |
|
2024-03-25 |
Other |
Machine Maintenance |
The performance on the cross seal dropped badly after the blade was cleaned by maintenance most recently. It's been having consistent issues ever since. We noticed the blades are no longer at the same height as each other (one is slightly higher) and they no longer meet each other at the corner. The tape on the pads was replaced, but the pads themselves have deep grooves in them, we flipped the cross seal pad to reduce this, which helped but hasn't eliminated the issue. |
|
|
replaced knive on the side seal |
