Sheeter
Location:
Pastry
Work Orders
Date requested |
Type | Problem | Cost | Time spent | Status | |
|---|---|---|---|---|---|---|
| 2021-10-13 | The egg sheeter cage fell and hit an employee's arm and face while she was cleaning it. It cut her nose. Cage will not stay up in the locked position when we are trying to clean it. | N/A | ||||
| 2021-09-30 | Sheeter guard falling very easily. Not sure if there's any way to make it lock in place a little more securely? | Complete | ||||
| 2021-08-12 | Egg sheeter guard was falling easily. | Complete | ||||
| 2021-07-21 | Other | Welding | The cage on the egg sheeter needs welding to be more secure. | repaired | ||
| 2021-07-03 | the sheeter blade has come loose from it's arm holder. the blade is on your work area. sheeter blade shouldnt be able to swing on the metal fastening on the end. | reinsstalled | ||||
| 2021-06-25 | The cage/ guard on the egg sheeter keeps falling down. | make certain cage is locked in postion | ||||
| 2021-06-21 | The cage on the egg free sheeter keeps falling down when it is supposed to stay up. It fell on someones arm. | unable to verify | ||||
| 2021-05-10 | Other | The pin on one of the sheeter blade's spring arms broke off. | repaired | |||
| 2021-05-01 | Other | Drain oil from sheeters, and refill with ATF to middle of sight glass. | Complete | |||
| 2021-02-12 | egg free sheeter is hesitating like a jerk when trying to feed things to the right. the belt on the left of the machine wont move for a while | parts are ordered | ||||
| 2021-01-02 | one of the blade that sits next to the roller on the egg sheeter is loose and won't sit flush with the roller. We have some cardboard to hold it in place currently. We miss placed the small plastic wedge, we may just need another one fabricated | 90 | Complete | |||
| 2021-01-01 | Other | Drain oil from sheeters, and refill with ATF to middle of sight glass. | Complete | |||
| 2020-12-27 | Other | blade for egg sheeter | The blade is missing a clip to keep the end together. Red tagged and left on the "egg" sheeter. | Complete | ||
| 2020-10-31 | Egg free sheeter (sheeter under DOR board in pastry) Won't stop running, so we manually turned it off and didn't use it the rest of the night. | Complete | ||||
| 2020-10-22 | the egg sheeter is missing screws for the panel. | Complete | ||||
| 2020-10-15 | The sheeter has a delay when going to sheet and acts like its struggling. | could not verify an issues, ran fine all morning | ||||
| 2020-06-23 | Other | sheeter | the front panel on the egg sheeter (on the mixer side) is currently being held on by masking tape and a sad screw. Can more screws be added to keep it attached to the machine? It keeps wanting to fall off. | installed screw | ||
| 2020-05-25 | The egg sheeter is making a loud noise when the left belt is running. The left bar also doesn't stay up really well. It kept falling on me when I tried to open it. | lubed bearing | ||||
| 2020-02-20 | The egg sheeter roller is uneven. The back side of the roller is tight. | repaired | ||||
| 2020-02-20 | Sheeter blade has a chip in it. | Complete | ||||
| 2020-01-17 | Other | Drain oil from sheeters, and refill with ATF to middle of sight glass. | Complete | |||
| 2020-01-01 | Other | Drain oil from sheeters, and refill with ATF to middle of sight glass. | complete | |||
| 2019-09-28 | Electrical | The sheeter by the DOR is slow to move left. And it sounds like there is a crackling noise coming from it. | ordered and replaced switch | |||
| 2019-09-17 | Other | The egg sheeter blade kept coming unlocked and becoming loose causing space between the blade and roller. This caused doughs to wrap around get caught and rip. | could not find a problem | |||
| 2019-07-31 | The sheeter blade is raised up on one side and the when we're sheeting the dough thinner it's getting caught and the dough is tearing. | In-Progress: Verifying, working fine | ||||
| 2019-07-17 | Sheeter blade needs the pin replaced.The pin is on the shelf under the sheeter table. | installed new pin | ||||
| 2019-06-14 | The sheeter facing the mixers is having some trouble with one of the blades being loose. The last two days we have had dough roll up under, over the roller. It is so loose I was able to fit my finger underneath. (left side blade) | 1.5 hrs | Completed | |||
| 2019-06-14 | I believe Amy B wrote a WO for the long sheeter by the mixers but I wanted to follow up. There is a gap between the rollers and the blades causing doughs to wrap around the rollers and tear. | Completed | ||||
| 2019-05-27 | Other | The sheeter blades were adjusted and need some more tweaking because now the blades are scraping the doughs. | Sheeter has been working fine. Possibly the blades were not in properly. | |||
| 2019-05-22 | Sheet close to mix area | |||||
| 2019-04-24 | The metal locks that lock in the blades are hard to lock into place. Could they please be greased or oiled, so there easier to move? | lubricated bearings, mat take a little while to loosen up | ||||
| 2019-04-21 | The blades on the sheeter need to be looked at. They're not flush with the roller and catching dough underneath. | not sure which sheeter you had issue with but both were run today without problems | ||||
| 2019-04-11 | Sheeter by mixers | The belt on the left side is really slow to start up and stops and starts while in use. Possibility of tearing the dough if the 2 belts are running at different speeds | replaced latch assy. | |||
| 2019-02-04 | The sheeter by the DOR is missing the part that holds the rollers in place. It was tied with a zip tie yesterday. We should be getting the replacement part on Friday. | |||||
| 2019-02-03 | Other | Egg free sheeter | The egg free sheeter has a broken component. You already saw it and put a zip tier on it. | Duplicate | ||
| 2019-01-31 | One of the individual wheels popped off the "wheels" for a 140qt bowl while we were moving it. Yikes! | lubricated and filled gear box | ||||
| 2019-01-31 | The sheeter by our DOR board is squeaking while in use and likely needs to be lubricated. | lubricated and filled gear box | ||||
| 2019-01-20 | One of the bars on the cage is detached and needs to be re-welded. There's tape on there to indicate. | welded bar | ||||
| 2018-12-18 | The pin on one of the sheeter blades popped out. Its from the sheeter against the wall. We taped the piece to the blade. This is an urgent fix- we will need to use by 8 AM on Thursday. Thank you!! | replaced pin | ||||
| 2018-11-11 | Electrical | The one against the wall | The cord is split. | taped cord | ||
| 2018-08-19 | SHEETER FACING MIX AREA | There seems to be oil leaking from the motor area (underneath the handle area) on the sheeter that faces the mix area. It is still working fine, but seemed odd. | ||||
| 2018-07-06 | Pin came out of the sheeter blades again | Chris Olsen replaced the worn OEM pin with a cotter pin. This seems to be a better and cheaper alternative to the unreliable OEM pins | ||||
| 2018-06-29 | Sheeter blade | One of the pins came out of the blades | Chris Olsen replaced pin Friday afternoon | |||
| 2018-05-10 | Other | Pin came out of the sheeter blade | 15 mins | complete | ||
| 2018-03-24 | old long sheeter | when marcus was working on kalacs the piece that holds the top blades on the left side snapped clean off the sheeter. We have the pieces in the managers office on the pastry desk. It looks as if we will have to order a new part entirely. | 33.00 | 30 | Complete | |
| 2018-03-24 | Other | Sheeter | Won't turn on at all. | 30mins | complete | |
| 2018-03-17 | Other | Sheeter | Sheeter is starting to pop up on the right side of the right blade. (>2-3mm gap size difference.) | 20 mins | complete | |
| 2018-03-02 | Other | old sheeter blade bracket broken | On right hand side of sheeter-arm/bracket that holds top of blade in place is broken. It holds blade in place and level at the top. We cannot use it until repaired in order to prevent further damage. | 180.00 | 15 mins | complete |
| 2018-02-24 | Other | *NEW* | Hey guys, can someone show us how to lock the ends of the new sheeter in the *up* position? It doesn't have the same latch as the others | 20 mins | complete | |
| 2018-02-04 | Other | *NEW* | The new sheeter is very squeaky when in use. In both directions. | 15 mins | complete |