Sheeter
Location:
Pastry
Work Orders
Date requested |
Type | Problem | Cost | Time spent | Status | |
|---|---|---|---|---|---|---|
| 2026-05-25 | 2 of our sheeter blades do not fit snugly around the rollers. They're very wiggly and the doughs tend to get trapped in there and shred | ordered new blades | ||||
| 2026-05-10 | Other | Drain oil from sheeters, and refill with ATF to middle of sight glass. | will change oil when replacing clutches | |||
| 2026-05-01 | Other | Drain oil from sheeters, and refill with ATF to middle of sight glass. | ok | |||
| 2026-02-22 | mixer side sheet made a really loud noise toward the end of assembly. It happened when we decreased the number to a lower setting while sheeting croissant dough during assembly. It happened twice, and it was when the numbers were lower, probably below 10. We were able to get the noise to stop after opening the dial wide. Machine works, just thought it would be good to take a look at it. | most likely has to do with clutch gears, of which I will be installing all new in the coming weeks/months | ||||
| 2026-02-04 | Other | equipment maintenence | Sheeter blade busted a pin, red-tagged on sheeter. | repaired | ||
| 2026-02-04 | Other | equipment maintenence | Sheeter blade busted a pin, red-tagged on sheeter. | duplicate | ||
| 2025-10-31 | Sheeter blade was dropped and the two pins on both sides broke off. Can these be replaced ASAP, as the sheeters are going to be in heavy use today? | repaired | ||||
| 2025-07-06 | Sheeter blade lost a pin. Red tagged and laying on the sheeter belt. Mixer side sheeter. Thanks! | repaired | ||||
| 2025-06-06 | Other | Equipment | Sheeter canvas breaking at seem. | replaced | ||
| 2025-06-04 | Other | The right side cage doesn’t stay locked in the up position on the mixer side sheeter. | knocked the tab again, I do this every time, about every 2 months... i will develop a longer term solution in the future | |||
| 2025-05-01 | Other | Drain oil from sheeters, and refill with ATF to middle of sight glass. | Oil color ok | |||
| 2025-04-08 | Other | Sheeter by the mixers. The right side cage will not stay up and locked. | repositioned | |||
| 2025-03-29 | Other | Mixer sheeter, There’s a bolt on the right hand side of the cage, on the back, that is loose and will come out all the way if pulled on. Amy B also knows which one it is. | repaired, added stop nut to back of screw... | |||
| 2025-03-04 | Other | equipment maintenance | One of the wall sheeter blades has a end joint piece that seems to have come apart. It looks like a peg & hole that are meant to be joined but are not currently. Image attached, red tagged and on the wall sheeter belt. | repaired | ||
| 2025-02-19 | Other | equipment maintenance | One of the sheeter blades' small wire connecting top to bottom has gone missing, blade is not usable in current condition. Image attached. | repaired | ||
| 2024-09-28 | Other | Pins missing for blades, wall sheeter | replaced | |||
| 2024-09-13 | The mixer side sheeter cage will not stay up. The left hand side. | Repaired | ||||
| 2024-08-11 | Right guard on sheeter not staying up. | adjusted | ||||
| 2024-08-01 | Can we put something on the back of the pegs on the sheeter so they don't slide out again? | You have to hit the sheeter table quite hard to get it to pop off. That is the first time that happened. | ||||
| 2024-05-01 | Other | Drain oil from sheeters, and refill with ATF to middle of sight glass. | drained and refilled with ATF | |||
| 2024-04-24 | Other | sheeter blade | replaced | |||
| 2024-04-21 | The blade is loose and has a gap from the roller. (egg sheeter) | They have been running all morning with no issue, this work order comes up a lot and I am thinking that the blade is not seated properly, take it out and reinstall | ||||
| 2024-03-17 | One of the blades on the egg sheeter has a pin that holds the two sides together break. We left the blade out on the belt to be fixed. | repaired | ||||
| 2024-03-12 | The egg sheeter no longer stops when the safety arms go up. | Blew flour out | ||||
| 2024-01-20 | Other | Egg sheeter right side cage is not holding in the up position | repaired | |||
| 2023-12-12 | The blade to the egg sheeter had the metal pin come out, so the blade is detached from the side. This will need to be repaired ASAP (I think it's a pretty quick fix) because we used the sheeters all day. | repaired | ||||
| 2023-11-18 | Other | egg sheeter safety cage bar | The lower bar on the left side of the egg sheeter is completely loose. | adjusted mechanism to not fall down on its own | ||
| 2023-06-28 | On the egg free sheeter, the blade on the left side is loose and tearing the dough. We will need the sheeter on Friday morning. | could not find an issue will see Alyce | ||||
| 2023-06-28 | I said we'd need the sheeter on Friday morning. I meant to write THURSDAY morning. Thanks! | dup | ||||
| 2023-06-12 | Egg free sheeter blade is loose and tearing doughs | complete | ||||
| 2023-05-13 | Other | Equipment Maintenance | Rollers are squeaky | |||
| 2023-05-01 | Other | Drain oil from sheeters, and refill with ATF to middle of sight glass. | drained and filled | |||
| 2023-04-23 | The grey pieces that hold the blades in place on the egg free sheeter. On the left side specifically, they are loose so the blades are bopping around and tearing the dough as we sheet it. See Cheryl | spoke with Cheryl we agreed that it was not in all the way | ||||
| 2023-04-16 | Other | Machine Maintenance | Egg Sheeter is squeaking a bit when rollers are running/changing thickness settings. | lubed | ||
| 2023-03-13 | The 'eggy' sheeter has a loose handle | Complete | ||||
| 2023-02-26 | The sheeter that's closest to the mixers won't turn on | replaced fuse and fuse holder | ||||
| 2023-02-26 | Egg free sheeter was pulsing on / off during use the other day. I would be sheeting and it would sporadically shut off and would have to keep resetting it. The plug does look pretty worn. | dup | ||||
| 2023-01-15 | Other | Egg sheeter- the cage closest to the kitchen doesn’t lock in place. Will fall if slightly bumped. | could not detect | |||
| 2022-11-08 | Electrical | The plug outlet is loose and sometimes the machine won't run. We have to remove plug and reinsert to make machine run. It does it randomly. | repaired plug | |||
| 2022-10-24 | The blade on the EGG SHEETER lost its pin. I saw Mike and showed him in person. | replaced | ||||
| 2022-10-13 | Electrical | Buy and install covers to protect BOTH sheeter 220 plugs and outlets from flour- fire hazard | unable to find any 220 covers for a 4x4 Duplex, I have never seen one | |||
| 2022-09-09 | Egg sheeter plug / outlet is loose | tightened | ||||
| 2022-07-03 | Other | handle on egg sheeter loose | The lever/handle to operate the Egg sheeter is loose. The sheeter facing the mix area. | tightened | ||
| 2022-06-27 | Other | The blades to sheeter closest to the mixers is still popping out. It’s on the right side, the top left side of the blades is the part that keeps coming out. It seems to happen at low numbers, like the piece isn’t moving with the rollers. Melissa, Alise, and River also can describe the problem. | Complete | |||
| 2022-06-11 | Other | The egg sheeter blades on the right side keep popping out of the holder. It is only the top left side that is coming out. | cleaned rollers | |||
| 2022-05-01 | Other | Drain oil from sheeters, and refill with ATF to middle of sight glass. | Complete | |||
| 2022-02-20 | Egg sheeter roller is uneven, which is resulting in doughs with inconsistent thickness. | Complete | ||||
| 2022-02-17 | Sheeter blade is broken. | Complete | ||||
| 2022-02-17 | Front metal covering is coming off. | Complete | ||||
| 2022-01-09 | Other | The blades on the egg sheeter don't seem to be lying quite flat. They have been tearing up doughs a little on the end further from the controls, and today gave us some trouble getting them off the machine for cleaning, and then when putting them back on. I think they're just a little warped, not sure if we can actually do anything about this though. | worked with pastry operator fine, I will order some new plastic for them |