LVO
Location:
Pastry
Work Orders
Date requested |
Type | Problem | Cost | Time spent | Status | |
|---|---|---|---|---|---|---|
| 2020-10-13 | Wash temp was running low | reset burner | ||||
| 2020-09-05 | LVO at the end of the shift started making a loud unusual sound when turned on, so we stopped using it for the night. | 2:00:00 | Complete | |||
| 2020-07-18 | Hook on wall by LVO is loose. Screws need to be tightened. | Complete | ||||
| 2020-07-09 | Other | In order for the wash temperature to be the correct temp, we always have to make sure the burner is pressed 30 minutes before taking the temp. Is there a way that we can eliminate this step and not have to press the button so much, and with such a specific timing? | only 1 reset today | |||
| 2020-06-24 | Electrical | The LVO wouldn't turn back on. We took off the back panel and none of the panels were lit up. We think that it might be the on/ off button isn't working? | tripped breaker, blew fuse, replaced FLM 10 A | |||
| 2020-05-30 | LVO wash temp. is not rising even with pressing the burner tonight. | chaanged pilot gas increase, ran fine today no issues | ||||
| 2020-05-11 | The sprayer hose next to the LVO is leaking water and water is pooling behind the LVO | replaced sprayer | ||||
| 2020-05-10 | Wash temp low | reset takes some time for temp. to get back up | ||||
| 2020-05-07 | Other | LVO, low wash temperature | LVO started the day with a wash temperature around 106°F and only rose to 120°F by noon. | It takes almost an hour to reach full temp. | ||
| 2020-03-24 | Wash temp on the LVO is low | fired up could not find issue | ||||
| 2020-03-19 | The LVO wash temp. starts out at the right temp. and then drops thru out the cycle. We think the pilot light might be out again. | working fine at this point | ||||
| 2020-03-17 | Wash temperature was low (around 100)- checked it multiple times and it didn't go up. | Assuming the burner was not lit, Reset | ||||
| 2020-03-16 | The door handle is stuck again. | see notes | ||||
| 2020-03-10 | I noticed our dishwashers have been recording the wash temps around 110 (supposed to be 150 min). After talking with them, they're saying the temp starts at 150 but then drops to 110 during the wash cycle. Is that how it's supposed to work? | I have been watching temps all day and it has held at 150 | ||||
| 2020-02-15 | LVO still acting up. | Complete | ||||
| 2020-02-10 | The wash temp was running a little low | reset burner | ||||
| 2020-02-08 | Plumbing | The LVO wash temp is below the minimum 150 temp that it should be. | operating fine | |||
| 2020-02-05 | Electrical | Really think we need a barrier for the motor of the LVO. Even though we don't pour liquid back there, the floor gets cleaned at least 3 times a day between Pastry for Cleaning and water is sprayed around the motor. Let's not risk it getting wet, please | we will not be dumping back there anymore | |||
| 2020-02-04 | Hose came loose on LVO and water was spraying everywhere. (we think it was the hose for the soap. Water pressure was very high and tube very small- used up all the soap quickly). Needs to be repaired before it can be used! Motor did get wet as a result. | repaired line | ||||
| 2020-02-02 | We need to cover up the LVO motor if it is not supposed to be wet. It actually was a problem for the last machine and caused it to break down a few times. And why risk our new machine being ruined after spending all this money for it? It will cost far less to put a barrier on it that anything happening to the motor if water gets in there. | |||||
| 2019-12-25 | The LVO wash temperature is running low. | complete | ||||
| 2019-12-21 | Plumbing | Water is coming out the side during its wash cycle and going on the floor. | see notes | |||
| 2019-12-21 | Other | grate replacement/sealing | The grate that covers the drain on the LVO stage is no longer connected to the drain. | |||
| 2019-12-16 | The LVO had low / inconsistent wash pressure | operating at 157 avg. all morning | ||||
| 2019-11-17 | The metal hinge is starting to crack. | replaced hinge | ||||
| 2019-10-13 | Plumbing | LVO won't turn on. I tried the Frankenstein switch on the wall but no dice. | Complete | |||
| 2019-09-29 | Missing screws on one of the "propellor" blades, causing it to spray water at door and have it leak out the bottom of door. | replaced missing screws | ||||
| 2019-09-19 | Electrical | The LVO keeps turning off when you go to start the wash cycle. | Complete | |||
| 2019-08-28 | Plumbing | Pipe came off on the big dish machine. needs to be put back on | Pipe came off on the big dish machine. Machine is still usable but the pipe still will need to be put back in place | attached pipe with screws | ||
| 2019-08-27 | Wash temp on LVO only reaching 120s at highest. Supposed to be 150. Still reaching 180 on rinse to sanitize. | When this happens turn off power, it will reset to proper temp. | ||||
| 2019-08-18 | The exhaust fan is not working. Also, some of the screws for the propeller on the left side are missing. | Complete | ||||
| 2019-08-14 | Plumbing | The LVO was dispersing a lot of steam from the top and making the dish room hotter then usual tonight. | functioning normally this morning | |||
| 2019-07-22 | The LVO has been leaking out more water than usual when it's cycling. We're guessing the seal on the door, both vertical and horizontal, may need replacing. It still functions fine, we just have to fill it more frequently. | Adjusted door sweep | ||||
| 2019-06-04 | The LVO wasn't holding pressure during the wash cycle. It was jumping up and down in pressure. It only happened once, but I still think it should be looked at. | is doing fine this morning | ||||
| 2019-05-27 | Plumbing | LVO wash temp is hovering between 25F and 30F | Wash Temp. is at 150 degrees and holding | |||
| 2019-05-23 | Piece on bowl rack for LVO needs to be re-welded | welded rack | ||||
| 2019-05-19 | The wheels for the bowl rack aren't working properly. They're spinning fine, just not turning properly. | installed new wheels | ||||
| 2019-04-22 | Plumbing | The bottom right "propellor" on the LVO is missing screws for half of it. It is still functioning but won't be for long. NEEDS ATTENTION SOON | replaced will drill out broken screws in morning | |||
| 2019-04-01 | The wash cycle will only come up to 120 degrees at the highest. Should be 150 minimum. The rinse is hitting 180 degree to sanitize. | Increased Hot water Heater temp.8 degrees | ||||
| 2019-03-31 | Plumbing | Grate over drain on the LVO stage keeps shifting around. | screwe plate down | |||
| 2019-03-31 | Plumbing | Grate over drain on the LVO stage keeps shifting around. | screwed down plate | |||
| 2019-03-16 | LVO wash pressure | The rinse pressure is not getting up to where it should and was consistently below 45 tonight. It kept jumping up and down with the pressure. | operating in normal parameters | |||
| 2019-03-01 | Today during a wash cycle with the LVO, the psi was fluctuating rapidly from 0 to 60. The rest of the day it seemed pretty normal. I am writing a work order just in case to have it looked at. | |||||
| 2019-02-26 | The LVO door handle is missing a screw on the interior handle. | replaced missing bolt | ||||
| 2019-02-24 | LVO | The LVO is dropping temperature for the sanitizing rinse. We noticed that the lower left propellor is loose and missing many screws. | fixed propeller and temp. is running ok this morning | |||
| 2019-02-05 | Plumbing | The LVO PSI was dipping and not staying where it should. It was reset and is now working fine. | ||||
| 2019-01-23 | Plumbing | There is a small hole in the LVO hose near where the handle connects. | repaired leak | |||
| 2019-01-02 | Plumbing | The lvo is dispensing a lot of soap while its running and the soap is leaking out all over the dish room floor. | I cycled through 5 times, working fine now will monitor today | |||
| 2018-12-09 | Plumbing | The nozzle isn't completely attached to the hose so when it's in use the pressure is causing it to slowly pop off | installed kit | |||
| 2018-12-07 | Plumbing | Soap dispenser | Water is continuously spraying into the soap dispenser on the LVO even when not on wash cycle. | it is working now but needs a rebuild kit on inlet water valve will order |